MENU
NOSHOK'S COVID-19 Response
Request Information
  • Switch adjustment ranges from vacuum through 6,000 psi depending on model
  • Standard Brass with NBR diaphragm wetted parts
  • SPST creep action switch with Silver-plated contacts
Unit of Measure

Specifications

Type

 N/A Mechanical Pressure Switch

Series

 N/A 100

Switching Function

 N/A Single Pole Single Throw (SPST), Normally Open

Switch Adjustable Range

 N/A 300 to 2,500 psig

Electrical Connection

 N/A Weatherpack Tower, 2-Pin Female, Attached to Flying Leads

Process Connection

 N/A National Pipe Thread (NPT) Male

Weight

 N/A 0.2 lb

Housing Material

 N/A Plated Steel

Optional Housing Material

 N/A Stainless Steel

Switch Type

 N/A Creep Action

Environmental Rating

 N/A Ingress Protection (IP69)

Switch Point

 N/A Field Adjustable and/or Factory Set

Hysteresis

 N/A <10% of Setpoint

Service Life

 N/A > 1,000,000 Load Cycles

Proof Pressure

 N/A 9,000 psi

Measuring Element

 N/A Zinc-Nickel Plated Steel, NBR Diaphragm

Warranty

 N/A 1 yr

Contact Rating

 N/A 100 V·A Maximum Voltage 42 Vdc

Process Connection Size

 N/A 1/8 in

Unit Net Weight

 N/A 0.2 lb

Switching Parameters

Switching Current

 N/A 2 A

Non-Repeatability

 N/A 1 psi or 5% of Setpoint

Contact Material

 N/A Silver-Plated

Optional Contact Material

 N/A Gold-Plated

Frequency [Max]

 N/A 60 cpm

Temperature Ranges

Media Temperature Range

 N/A -25 to 85 ºC-13 to 185 ºF

Ambient Temperature Range

 N/A -25 to 85 ºC-13 to 185 ºF

Application

Application

 N/A
  • Hydraulics & pneumatics
  • Pumps & compressors
  • Tank monitoring
  • Leak detection
  • Water management

Prop 65 Warnings

Prop 65 Warnings

 N/A
WARNING: This product can expose you to chemicals including Lead and Nickel, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Limitations Which Apply Are

Limitations Which Apply Are

 N/A These units must be operated within the catalogued environmental and application parameters. Determination of failure will be made by NOSHOK, Inc.'s equipment and personnel or a certified test facility specializing in this type of evaluation. Gauge failures determined to be caused by over-range, incompatibility with environment or product media and abuse will not be considered under this warranty. NOSHOK, Inc. will, at its discretion, repair or replace the working parts of the damaged gauge without cost to the customer.

In keeping with and for purposes of product and/or manufacturing process improvements, NOSHOK, Inc. reserves the right to make design changes without prior notice.

Options and Accessories

Distribution Manifolds

 N/A NOSHOK's Distribution Manifolds connect multiple instruments to one diaphragm seal, eliminating multiple connections that lead to possible leak paths.

Mechanical Switches Options & Accessories

 N/A Factory Adjusted Switch Point (Specify)

Pressure Snubbers - Piston Type

 N/A
  • Resist clogging and are self-cleaning
  • Five different sized pistons included with each snubber to ensure the correct amount of snubbing for virtually every application
  • Available in Brass and 316 Stainless Steel in 1/4" NPT, 1/2" NPT or SAE J1926-3: 7/16-20
  • Weight approximately 0.2 lb. for 1/4" & 7/16", and approximately 0.4 lb. for 1/2"

Pressure Snubbers - Sintered Type

 N/A
  • Cost effective solution to protect expensive instrumentation
  • Increases gauge readability by smoothing out pressure surges, pulsations and spikes
  • 5 basic elements available for each snubber to accommodate specific application needs
  • Snubbing action achieved by utilizing a corrosion resistant 316 Stainless Steel sintered porous element
  • Exotic materials or intermediate disc grades available
  • Provides long service life with no moving parts to wear out
  • Weight approximately 0.2 lb. for 1/4" & 7/16", and approximately 0.4 lb. for 1/2

Steam Syphons

 N/A
  • Protect the instrument from the damaging effects of high temperature steam
  • Recommended for use in all steam applications
  • Available in 1/4" and 1/2" NPT sizes in welded steel, welded 316 Stainless Steel or seamless 316 Stainless Steel with ratings to 3,800 psi at 850 ºF

Swivel Adapters

 N/A
  • Temperature ratings: 15,000 psi at 200 ºF and 3,000 psi at 1,000 ºF
  • Used with gauges and gauge valves to adjust the line of sight
  • Rotates 360º to allow the connected instrument to be positioned in the desired direction
  • The pressure connection is achieved with a tapered cone style compression fitting simply by tightening the swivel hex nut
  • All 316 Stainless Steel construction
  • Standard with 1/2" NPT male process - 1/2" NPT female instrument connections
  • Also available with 1/4" NPT connections, same specifications apply
  • Weight approximately 0.8 lb.